ARMY TM 5-6675-308-12
MARINE CORPS TM 08837A-12/1A
Battery box contains acid-filled batteries
(3) Remove four bolts and washers which secure
which may generate hydrogen gas. Keep
subfloor plate to subfloor mounting bracket.
heat and ignition sources away. Do not
Remove subfloor plate.
allow battery liquid to touch skin or
(4) Reinstall or retain hardware as appropriate.
clothing. If battery liquid touches skin,
flush area immediately with water; if it
b. Subfloor Plate Replacement.
touches the eyes, flush immediately with
water for 30 minutes and see a physician
(1) Install subfloor plate as described in paragraph
without delay.
(1) Removal.
(2) Install primary pallet, battery box, and other
Remove battery box top. (See figure 2-8.)
(a)
equipment.
Loosen nut securing cable assembly W11
(b)
c. Subfloor Mounting Bracket Removal.
negative battery terminal adapter to nega-
tive battery post; remove cable assembly
(1)
Remove battery box, primary pallet, and other
W11 negative battery terminal adapter
equipment.
from negative battery post.
(c)
Disconnect battery terminal adapter on ca-
(2)
Remove four bolts and washers which secure
ble assembly W6 from negative terminal of
subfloor mounting bracket to subfloor plate.
battery.
(3)
Remove two nuts and washers from pintle
Disconnect battery terminal adapter on ca-
(d)
bolts which secure subfloor mounting bracket
ble assembly W11 from positive terminal of
to utility truck. Remove subfloor mounting
battery; remove cable assembly W11 from
bracket.
battery box.
Disconnect battery terminal adapter on ca-
(4)
Reinstall or retain hardware as appropriate. If
(e)
ble assembly W6 from positive terminal of
a new subfloor mounting bracket is not being
battery; remove cable assembly W6 from
installed, replace pintle bolt nuts and washers.
battery box. Remove battery terminal cover
from battery terminals.
d. Subfloor Mounting Bracket Replacement.
Inspect all battery terminal adapters and
(f)
(1) Install subfloor mounting bracket as described
cable assemblies W6 and W11. If service-
able, perform maintenance in accordance
with TM 9-6140-200-14. If unserviceable,
(2) Install primary pallet, battery box, and other
discard and install new equipment in (2)
equipment.
following.
e. Utility Truck CDU Bracket Removal.
Remove nuts, washers, hook bolts, and bat-
(g)
tery retainers. Inspect and, if serviceable,
(1) Release two clamping catches and remove
perform maintenance in accordance with
C D U from v e h i c l e CDU bracket. (See
TM 9-6140-200-14. If unserviceable, discard
and install new equipment in (2) following.
(2) Remove two screws and lockwashers and bolt,
(h)
R e m o v e batteries with battery carrier.
lockwasher, and nut securing vehicle CDU
Clean battery box chassis in accordance
bracket in place; retain hardware. If a new
with TM 9-6140-200-14.
CDU bracket is not being installed, replace
Install batteries in accordance
(2) Replacement.
screws and lockwashers in instrument cluster
with paragraph 2-10.
and handle.
f. Utility Truck CDU Bracket Replacement. In-
a. Subfloor Plate Removal.
stall utility truck CDU bracket as described in para-
graph 2-8b or 2-9b as applicable.
Remove battery box, primary pallet, and other
(1)
equipment. (See figure 2-4.)
g. Cable Assembly W7 Removal.
Remove two bolts, nuts, and washers which
(2)
(1) Remove right front seat of utility truck and
secure subfloor plate and seat belt hardware (if
remove battery compartment cover. (See fig-
installed) to utility truck bed; retain all serv-
ure 2-6.)
iceable hardware.
4-39
Previous Page
