ARMY TM 5-6675-308-12
MARINE CORPS TM 08837A-12/1A
Disconnect cable assembly W3 connector
and secure with four clamps, washers, and
(b)
W3P2 from computer connector 1J4.
screws. (See figure 4-7.)
Disconnect cable assembly W1 connector
(c)
(c) Install computer in primary pallet and se-
W1P2 from computer connector 1J3.
cure with four captive screws. (See figure
4-2.)
Loosen four captive screws securing com-
(d)
uter to primary pallet; remove computer.
( d ) Connect cable assembly W3 connector
(See figure 4-2.)
W3P2 to computer connector 1J4. (See fig-
ure 2-9. )
Disconnect cable assembly W5 connector
(e)
W5P4 from computer fan connector 5J1.
( e ) Connect cable assembly W2 connector
W2P2 to computer connector 1J1.
Loosen four screws, washers, and clamps
(f)
securing computer fan to mounting plate;
( f ) Connect cable assembly W1 connector
remove fan.
W1P2 to computer connector 1J3.
Remove three nuts, lockwashers, and wash-
(g)
ers securing fan guard to mounting plate;
and replace protective cover as follows:
remove fan guard. (See figure 4-7.)
(1) Removal.
(2). Replacement.
(a) Release catch and lift up protective cover.
Secure fan guard to mounting plate with
(a)
three nuts, lockwashers, and washers.
(b) Remove three screws and washers securing
protective cover to frame; remove protec-
C o n n e c t cable assembly W5 connector
(b)
tive cover.
W5P4 to computer fan connector 5J1. (See
(2) Replacement.
Install computer fan on mounting plate,
(c)
(a) Secure protective cover to frame with three
oriented with airflow arrow pointing up,
screws and washers.
and secure with four clamps, washers, and
(b) Close protective cover and secure with
screws. (See figure 4-7.)
catch.
Install computer in primary pallet and se-
(d)
cure with four captive screws. (See figure
place flashlight as follows:
4-2.)
(1) Removal. Loosen clamp and slide flashlight
C o n n e c t cable assembly W3 connector
(e)
away from flashlight holder; remove flashlight.
W3P2 to computer connector 1J4. (See fig-
ure 2-9.)
(2) Replacement. Install flashlight so that it is
C o n n e c t cable assembly W2 connector
snapped to flashlight holder and encircled by
(f)
W2P2 to computer connector 1J1.
clamp; tighten clamp.
C o n n e c t cable assembly W1 connector
(g)
W1P2 to computer connector 1J3.
and replace flashlight holder as follows:
(1) Removal. Remove two T-handles securing
replace belt assembly as follows:
flashlight holder to frame; remove flashlight
holder. Remove flashlight.
(1)
and washers and one retainer securing belt
Install flashlight holder and
(2) Replacement.
assembly to frame; remove belt assembly.
lightly secure to frame with two T-handles.
With flashlight installed, slide flashlight holder
Replacement. Secure belt assembly to frame
(2)
until flashlight beam is centered on porro
with two screws, washers, and lockwashers and
prism; tighten two T-handles.
one retainer.
follows:
(1) Removal. Remove four screws and washers
(1) Removal.
securing plumb bob assembly to mounting
plate; remove plumb bob assembly.
(a) Disconnect cable assembly W2 connector
(2) Replacement. Secure plumb bob assembly to
W2P2 from computer connector 1J1. (See
mounting plate with four screws and washers.
4-35
Previous Page
