ARMY TM 5-6675-308-12
MARINE CORPS TM 08837A-12/1A
(2) Connect. Transfer cable W8, located in top of bat-
n. Connect cable W9 connector W9P2 to connector P1
tery box, between power supply connector 3J4 and
of adapter cable.
power cable W7 connector W7P1.
o. Connect adapter cable connector P2 to personnel res-
(3) Set PS VEHICLE circuit breaker CB2 to ON.
cuc hoist connector, J119. (See view B, figure 3-14.)
BATT indicator will go out. (CHRG indicator
may light.)
p. Set personnel rescue hoist power circuit breaker to
ON. Set PS VEHICLE circuit breaker CB2 to ON.
d. Remove two forward T-handles securing clamping
BATT indicator will go out.
brackets to vehicle's subfloor or mounting base and
store on PADS primary pallet.
q. Set PS BATTERY circuit breaker CB1 to OFF.
BATT indicator will light. Disconnect battery cable
e. Slide primary pallet forward several inches to disen-
W6 from power supply connector 3J2.
gage alignment pins. Remove two rear T-handles se-
curing alignment pins bracket and store the T-handles
r.
Lift primary pallet into helicopter and locate it on
on PADS primary pallet.
cargo platform with porro prism facing outward.
f.
Set PS BATTERY circuit breaker CB1 to OFF.
BATT indicator will light. Disconnect battery cable
Adjust pallet until PADS is positioned approximately
s.
W6 from power supply connector 3J2.
as shown in figure 3-14, so that plumb bob can hang
down between helicopter fuselage and landing skid.
g. Position the primary pallet so it can be safely lifted
(see figure 3-15.)
out of the vehicle by three persons. Lift the pallet out
and move it about 5 feet behind the vehicle.
Open PADS top panel marked "NO SEAT" and, us-
t.
ing the two belt assemblies from the helicopter's tool
h. Place battery box on the ground near the primary pal-
kit, tie down primary pallet attaching belts to floor
let. Connect battery cable W6 connector W6P1 to
rings as shown in figures 3-14 and 3-16.
power supply connector 3J2. Set PS BATTERY cir-
cuit breaker CB1 to ON. BATT indicator will go out.
u. Tighten belt assemblies, using ratchet handles, and
close "NO SEAT" top panel.
When the helicopter approaches, set PS VEHICLE
i.
circuit breaker CB2 to OFF. BATT indicator will
light. Disconnect transfer cable W8 connector W8P2
v. Transfer the battery box to the cargo platform and po-
from power cable W7 connector W7P1 and power
sition approximately as shown in figure 3-14. Install
supply connector 3J4. Drive the vehicle outside the
battery belt assembly through handles and fasten to
landing area. Stow transfer cable W8 in top of battery
floor rings on both sides of the box.
box.
w. Connect battery cable W6 to power supply connector
Connect cable W9 (located in top of battery box) con-
j.
3J2. Set PS BATTERY circuit breaker CB1 to ON.
nector W9P1 to power supply connector 3J4.
BATT indicator will go out.
k. Pilot is to land the helicopter so the starboard cargo
x. Without disconnecting cable W1, remove CDU from
door is as close to the primary pallet as possible.
computer bracket and secure to helicopter leg mount
Check that helicopter personnel rescue hoist power
(located in battery box top). Route to passenger seat.
circuit breaker is OFF. Secure the starboard cargo
door in the fully-open position.
Select the new lever arms for the helicopter. Refer
y.
to paragraph 3-8.1 b (3).
l.
Prepare helicopter for PADS transfer as described in
z.
Secure helicopter doors. If removed previously, rein-
stall radio, spare tire, and gas can on vehicle. Load
m. Pull down headliner panel located over PADS mount-
survey and personal gear that will not be used
ing area to expose personnel rescue hoist connector,
during the helicopter mission onto the vehicle.
J119.
aa. During flight, strap the CDU to the operator's
left leg. (See figure 3-9, sheet 2.)
3-52
Change 2
Previous Page
