ARMY TM 5-6675-308-12
MARINE CORPS TM 08837A-12/1A
OPERATOR ACTION
DATA DISPLAY
contains seven standard U.S. Army vehicles and has the
Press MON, ID, 5, 1, ENT
Vehicle initially
capability of having the operator add lever arm information
entered
for up to three nondefined vehicles. Reference the specific
Press CLR
51E
"8-10"
vehicle installation for sight/plumb bob location. The
standard vehicles in the order of selection and CDU displays
Press 8, ENT
51X
.
follow. The program will display the last vehicle entered
Press +, 7, 6, 2
during the initialization, i.e., if the OH-58 had been selected
51+
.762
before the system was turned off, the CDU at turnon would
Press ENT
51Y
.
indicate OH-58 5.
Press -, 1, 6, 5, 8, ENT
51Z
.
Press -, 6, 1, 0, ENT
51V
.
Plumb Bob or
CDU
QUE
Vehicle
Sight Location
Press -, 4, 9, 5, ENT
SEL 1 8
HMMWV
Left side driver
1. HUM
1
Press - to scan ID's 50, 49, 48, and 47 to verify
the entered values are correct. Above operator
sight/plumb bob
action must be repeated if a change is to be
CUCV
Pintle mounted
2
2. CUV
made.
plumb bob
(2) In the event more than one nonstandard vehicle
3
3. SUV
Left side driver
SUSV
is to be entered into memory, repeat above oper-
sight/plumb bob
ator action making sure that when performing
Jeep
4
Pintle mounted
4. M151
third step, a number other than the one previous-
plumb bob
ly entered is used, i.e., 9 or 10. If the number 8
5
5. OH-58
OH-58
PADS mounted
were entered again, X, Y, Z, and V dimensions
Helicopter
plumb bob arm
previously entered would be cleared from mem-
ory. A save routine at shutdown will store all
6
UH-1
PADS mounted
6. UH-1
nonstandard vehicle selections which have been
Helicopter
plumb bob arm
entered.
7
PADS mounted
M151 Jeep
7. PLMB
plumb bob arm
(3) In the event a vehicle selection change is neces-
sary during a mission, the new vehicle lever arms
may be selected by returning to the monitor
table and proceeding as follows:
a. The operator presses CDU +/2 or -/8 advance or
decrement the vehicle selection until the correct
OPERATOR ACTION
DATA DISPLAY
vehicle has been displayed, then presses ENT. The
vehicle selection may be changed at any time during
Press ID, 5, 1, ENT
Vehicle previously selected
operation, which allows vehicle to vehicle transfer
while the system is operational.
When number of selected vehicle is displayed,
press ENT.
b. If the system has been installed in a vehicle which
Press MON, 1
HUM 1
is not defined as one of the seven standard vehicles,
Press MON, 2
CUV 2
or has not had the lever arm previously entered, the
operator must enter any choice of vehicles, in order
Press MON, 3
SUV 3
to proceed with the initialization. The procedure
Press MON, 4
for selecting and inserting data for the nondefined
M151 4
vehicle is as follows:
Press MON, 5
OH-58 5
Press MON, 6
UH-1 6
(1) While PADS is aligning or preferably after align-
ment is complete, the operator may insert up to
Press MON, 7
PLMB 7
three nonstandard vehicle selections after deter-
Press MON, 8
SEL 1 8
Only displayed if
mining the X, Y, Z, and V lever arm dimensions
entered per non-
using figure 3-5.1 as an example. All lever arm
Press MON, 9
SEL 2 9
standard vehicle
entries and displays must be in meters to the
procedure
Press MON, 10
nearest millimeter.
SEL 3 10
3-14
Change 2
Previous Page
