TM 11-5826-225-35
spring into hole in hubbed spur gear
collar should be against spur gear
(64).
(96).
(23)
Place spur gear (62) on assembly of
H o l d hubbed spur gear (94), and
(34)
(33) above. Position spur gear (62)
rotate spur gear (96) six teeth clock-
so that other end of load spring (63)
wise (right-hand loading), as viewed
fits into hole in spur gear (62).
from spur gear (96) end. Take up any
slack before counting the six teeth.
Place collar (61) on hub of hubbed
(35)
spur gear (64). The chamfered end of
Keep right-hand loading as in (23)
(24)
collar should be against spur gear
above, and place assembly of items (94
(62).
through 98) on shaft of resolver B3
(110). Mesh spur gears (94 and 96)
Place assembly (60 through 64) on
(36)
with 17-tooth gear of spur gear as-
shaft of tuning synchro control trans-
sembly (84) which is nearest resolver
former B1.
B3.
Lightly tighten two setscrews (60)
(37)
just enought to hold assembly ((36)
Tighten two setscrews (97, lock). Do
(25)
above) in place.
not tighten setscrews on openings in
split hub of hubbed spur gear (94).
P l a c e load spring (91) on hub of
(38)
Tighten setscrews on solid portion of
hubbed spur gear (92). Insert one end
split hub.
of load spring into hole in hubbed
spur gear (92).
Mount motor 132 (39) to rear gear
(26)
Place spur gear (90) on assembly of
plate (58) with two screws (85), two
(39)
lockwashers (86), and two flat
(38) above. Position spur gear (90)
so that other end of load spring (91)
washers (87).
fits into hole in spur gear (90).
(27)
Attach screws (8) and terminal lugs
Place collar (89) on hub of hubbed
(40)
(9) to tuning synchro control trans-
spur gear (92). The chamfered end of
former B1 (10).
collar should be against spur gear
(28) M o u n t B1 (10) to rear gear plate
(90).
( 5 8 ) with three screws (5), three
Place assembly of items (88 through
lockwashers (6), and three rim clamps
(41)
9 2 ) on shaft of bearing synchro
(7).
transmitter B4 (50).
(29) Mount servo motor-generator set MG1
(42)
Lightly tighten two setscrews (88)
(17) to rear gear plate with three
just enough to hold assembly ((41)
screws (18), three lockwashers (19),
above) in place.
and three rim clamps (20).
(43) Attach two extension springs (66) to
(30) Mount servo motor B5 (47) to rear
hubbed tuning capacitor drive gear
gear plate with two screws (44), two
loci-mashers (45), and two rim clamps
(65).
(46).
(44) P l a c e tuning capacitor drive gear
(67) on hub of hubbed tuning capaci-
(31) Attach screws (48) and terminal lugs
(49) to bearing synchro transmitter
tor drive gear (65). Countersunk holes
in gear (67) go toward hubbed gear
B4 (50).
(65). Attach other ends of extension
(32) M o u n t B4 (50) to rear
gear plate
springs (66) to gear (67).
with three screws (51),
three lock-
(45) Place collar (69) on huh of hubbed
washers (52), and three
rim clamps
gear (65), and lightly tighten two set-
(53)
screws (68).
(33) Place load spring (63)
on hubbed
spur gear (64). Insert one
end of load
(46) Place assembly of items (65 through
3-7
Previous Page
