ARMY TM 5-6675-308-12
MARINE CORPS TM 08837A-12/1A
.
.
b. SUSV PADS Modifications. Before PADS can be
and, with the screwdriver, install screws in bottom
installed, the SUSV inner body must be drilled to provide a
two holes of the engine access panel. The cable
hole for the battery vent tubing and the vehicle wiring harness
should be loose in the clamps so it can slide back
must be modified, These operations must be performed by
and forth.
direct support maintenance personnel in accordance with TM
(3)
5-6675-308-34 or Marine Corps TM 08837A-34/2.
Bob Assembly Installation . The plumb
bob assembly fits just inside the left front of
c. SUSV Kit Installation.
vehicle, beside the driver. Obtain, from the
installation kit, the plumb bob assembly (item 28,
(1)
. Obtain the following
items from the SUSV installation kit and proceed
follows:
(a) Using a 10-mm open-end wrench, install the
plumb bob bracket on the driver's seat and
backrest supports located inside the driver's
door. Use the four bolts loosely installed in the
supports.
two O-rings (1.478-1 .490 ID), one .375 -24UNF x
1.75 lg bolt one .375 flat washer, two .312-24UNF
(b) Install the bracket so that the pin for rotating
x .875 lg bolts, two .312 flat washers, and one no.
the plumb bob arm is located to the front of
6-32UNC-2A x .312 lg screw.
(a) Remove four of the six bolts for the heater
(4)
. Obtain floor
access plate and brace from the SUSV (see
(b) Install lower bracket using existing hardware.
proceed as follows
(c) Retrieve dash panel handle and the two bolts
and upper plate from kit.
(a) Insert the four bolts into the tapped holes in
the floor of the vehicle from the inside.
(d) Place dash panel handle on top of upper plate,
(b) Thread bolts by hand or use a 13-mm wrench,
align holes, insert bolts, and hand-tighten.
full length into the holes to clean threads.
(e) Attach tube to lower bracket using radial
(c) Remove bolts from holes.
washer, 3/8 bolt, and flat washer. Hand-tighten.
(d) Place frame assembly into the vehicle with
Fit clamp around tube at the top and attach to
(f)
battery compartment located to the rear.
upper bracket using two 5/16 belts and flat
washers. Hand-tighten.
(e) Align the four holes of the frame (in battery
compartment) with threaded holes in the vehicle
(g) Check that all hardware is in place without
floor.
stress. Tighten all bolts and screws.
(f) Place floor support plate underneath the vehicle,
(h) Attach quick-release pin and the 10-inch long
aligning holes with frame assembly, Apply
piece of chain using No. 6-32UNC-2A x .312 lg
anti-seize compound, from installation kit, to
screw on CDU mounting bracket.
the bolts, and thread from underneath the
vehicle through the holes to the inside. Tighten
Install two O-rings on mount tube in slots
bolts to pull the plate into position flush with
provided.
the outside of the vehicle. Add washers and
nuts and hand-tighten.
Install CDU mounting bracket on mount tube
and secure with quick-release pin.
(g) Align the forward end of frame assembly with
two holes on the passenger seat rails.
(2)
Obtain two cable clamps
(h) Bolt the forward end of frame to seat rails using
cable W1. Place the two clamps from the kit
two 5/16-24 UNF bolts, nuts, and washers from
around cable W1 near connector WlP1 and 4J1
kit. Hand-tighten.
2-56
Change 2