ARMY TM 5-6675-308-34
MARINE CORPS TM 08837A-34/2
b. Replacement.
a. Removal. Remove rivets securing part by drilling
or other suitable means; remove part.
(1) Secure shock and vibration isolator mount (5)
to base (6) and mounting chassis (10) with 8
b. Replacement.
screws (2 and 7) and 16 `washers (3, 4, 8, and
(1) Secure part in position with rivets.
9).
(2) Swage rivets in place.
(2) Remove block from under mounting chassis
the PADS transit case consists of replacing the shock
(3) Replace cover (1) and secure with latches.
and vibration isolator mounts (8, figure 3-14).
a. Removal.
tion kit consists of removing heater air intake system,
(1) Release latches and remove cover (l).
removing rear panel, installing side and bottom mount-
ing plates on rear panel, installing angle bracket on rear
NOTE
panel, installing nut plates on vehicle body, cutting out
rear panel to install door and frame, installing door
Pin housing (5) must be removed to re-
frame, installing porro prism door on rear panel, install-
place two of the shock and vibration
ing transition joint and flexible heater hose, installing
isolator mounts.
the CDU winter mounting bracket, and installing rear
(2) Remove two screws (2), lockwashers (3), and
panel in vehicle.
washers (4) securing pin housing (5) to pallet
a. Remove Heater Air Intake System.
mounting base (12); remove pin housing.
(1) Remove four sheet metal screws securing air
(3) Place a block under the pallet mounting plate
intake pipe to heater flange and air intake
(12) to prevent it from tiltin when a shock
duct. (See figure 3-16, sheet 1).
and vibration isolator mount (8) is removed.
(2) Remove four bolts, washers, and nuts securing
(4) Remove four bolts (6), washers (7), screws (9),
air intake duct to rear panel.
washers (11), and lockwashers (10) securing
.
shock and vibration isolator mount (8) to pal-
(3) Remove air intake pipe and duct. Return them
let mounting base (12); remove mount.
to the supply system.
b. Replacement.
(4) Reinstall the four bolts, washers, and nuts
removed in step (2) above in the holes in the
(1) Secure shock and vibration isolator mount (8)
rear panel.
to pallet mountin base (12) with four screws
(9), lockwashers (10), washers (11), bolts (6),
b. Remove Rear Panel.
and washers (7).
(1) Remove spare tire and fuel can from utility
(2) Remove block from under pallet mounting
truck.
plate (12).
(2) Remove 18 bolts, washers, and nuts securing
(3) Secure pin housing (5) to pallet mountin base
rear panel to utility truck body; remove rear
(12) with two screws (2), lockwashers (3), and
panel and place protective cloths on electrical
washers (4).
equipment.
(4) Replace cover (1) and secure with latches.
the IMU transit case consists of replacing the shock and
Exercise care to prevent damage to gas-
vibration isolator mounts (5, figure 3-15).
ket cemented around periphery of panel.
a. Removal.
(3) Clean any caulking compound from edges of
rear panel and utility truck body.
(1) Release latches and remove cover (1).
c. Install (Left and Right) Side Mounting Plates,
(2) Place a block under the mounting chassis (10)
to prevent it from tiltin when a shock and
880524-1 and -2, Plate 880526-1, and Handles
on Rear Panel.
vibration isolator mount (5) is removed.
(1) Place side mounting plate 880524-1 (7, figure
(3) Remove 8 screws (2 and 7) and 16 washers (3,
4, 8, and 9) securing shock and vibration isola-
rear panel. Locate side mounting plate so that
tor mount (5) to base (6) and mounting chassis
(10); remove mount.
3-44
Previous Page
