TM 5-6675-296-24P
in SB 708-42 which is used to identify the manufac-
(3) Recoverability Code. Recoverability codes
turer, distributor, or Government agency, etc.
are assigned to support items to indicate the
disposition action on unserviceable items. The
f. Description. Indicates the Federal item name
recoverability code is entered in the fifth position
and, if required, a minimum description to identify
of the Uniform SMR Code format as follows:
the item. Items that are included in kits and sets
are listed below the name of the kit or set, with the
Recoverability
quantity of each item in the kit or set indicated in
Definition
Code
the quantity incorporated in unit column. When
Z
Nonreparable
item.
When
the part to be used differs between serial numbers
unserviceable, condemn and dispose at
of the same model, the effective serial numbers are
the level indicated in position 3.
shown as the last line of the description. In the
Reparable item. When uneconomically
O
Special Tools List, the initial basis of issue (BOI)
reparable, condemn and dispose at
appears as the last line in the entry for each special
organizational level.
tool, special TMDE, and other special support
equipment. When density of equipments sup-
F
Reparable item. When uneconomically
ported exceeds density spread indicated in the
reparable, condemn and dispose at the
basis of issue, the total authorization is increased
direct support level.
accordingly.
H
Reparable item. When uneconomically
g. Unit of Measure (U/M). Indicates the stand-
reparable, condemn and dispose at the
ard of the basic quantity of the listed item as used
general support level.
in performing the actual maintenance function.
Reparable item. When beyond lower
D
This measure is expressed by a two-character
level repair capability, return to depot.
alphabetical abbreviation (e.g., ea, in., pr, etc.).
C o n d e m n a t i o n and disposal not
When the unit of measure differs from the unit of
authorized below depot level.
issue, the lowest unit of issue that will satisfy the
L
Reparable item. Repair, condemnation,
required units of measure. will be requisitioned.
and disposal not authorized below
h. Quantity Incorporated in Unit. Indicates the
depotspecialized repair activity level.
quantity of the item used in the breakout shown on
Item requires special handling or
A
the illustration figure, which is prepared for a
condemnation procedures because of
functional group, subfunctional group, or an
specific reasons (i.e., precious metal con-
assembly. A "V" appearing in this column in lieu
tent, high dollar value, critical material
of a quantity indicates that no specific quantity is
or hazardous material). Refer to ap-
applicable (e.g., shims, spacers, etc.).
p r o p r i a t e m a n u a l s / d i r e c t i v e s for
specific instructions.
4. Special Information.
c. National Stock Number. Indicates the Na-
a. Usable on codes are shown in the description
tional stock number assigned to the item and will
column. Uncoded items are applicable to all
be used for requisitioning purposes.
models.
d. Part Number. Indicates the primary number
Used On
Code
used by the manufacturer which controls the
Model T2-68 MIL
CRR
design and characteristics of the item by means of
Model T2-68 MIL
CRS
its engineering drawings, specifications standards,
b. Repair parts kits and gasket sets appear as
and inspection requirements to identify an item or
the last entries in the repair parts listing for the
range of items.
figure in which its parts are listed as repair parts
NOTES
are listed at the end of the repair parts listings for
When a stock numbered item is requisi-
the last figure containing parts of the kit.
tioned, the repair part received may
c. The following publication pertains to
have a different part number than the
Theodolite, Directional and its components:
part being replaced.
TM 5-6675-296-14 Operator's, Organizational,
e. Federal Supply Code for Manufacturer
DS and GS Maintenance
(FSCM). The FSCM is a 5-digit numeric code listed
Manual
3
Previous Page
